Cording Foot za ušivanje uzice do 2mm debljine-bernette b42_b48_b62_b68

34,90  sa PDV

Dostupno za isporuku odmah

šifra: 5020405117

Cording Foot za ušivanje uzice do 2mm debljine
za bernette Funlock b42/b48/b62/b68

Sa stopicom za užad s vodilicom za užad možete izraditi obrube, nabore s užetom i ukrasne rubove.
Ova stopica vodi ukrasne i fine uzice debljine do 2 mm točno i precizno ispod šava pokrovnog šava dok se šivaju.
Alternativno, također se može koristiti za izradu i umetanje cjevovoda.

Za šivanje užeta:

1. Namjestite stroj za „Coverstitch narrow”, koristeći igle D&E

2. Podignite stopicu i promijenite je na “Cording stopicu”.

3. Umetnite “Cording Guide” u rupu na lijevoj prednjoj strani ploče za ubod i u razmak između poluge za smotani porub i poklopca za ubod.

4. Napomena: može se koristiti kabel promjera do 1/16” (2,0 mm).

5. Umetnite kabel u rupu “vodilice za kabel”, zatim kroz utor “stopice za kabel”.

6. Povucite rep kabela oko 2” (50 mm) iza stopala.

7. Provucite tkaninu ispod stopala i iznad užeta.

8. Spustite stopicu i šivajte, vodeći uzicu iza stopice kada počinjete šivati.

Za šivanje cijevi:

1. Postavite stroj za „lančani ubod”, pomoću igle D.

2. Podignite stopicu i promijenite je na “Cording stopicu”.

3. Napomena: “Cording guide” se ne koristi za ovu funkciju.

4. Napomena: može se koristiti kabel promjera do 1/16” (2,0 mm).

5. Umetnite uže kroz utor na “Nožici za užad”.

6. Omotajte tkaninu oko užeta ispred stopala. Provucite tkaninu ispod stopala.

7. Spustite stopicu i šivajte preko tkanine.

8. Napomena: Držite uže iza stopala kada počinjete šivati.

Ova stopica vodi ukrasne i fine uzice debljine do 2 mm točno i precizno ispod šava pokrovnog šava dok se šivaju.
Alternativno, također se može koristiti za izradu i umetanje cjevovoda.

Cording Foot – With the Cording Foot with Cording Guide, you can create piping, corded tucks and decorative trims.
This presser foot guides decorative and fine cords of up to 2 mm thickness exactly and precisely below the coverstitch seam as they are being sewn on.
Alternatively, it can also be used to create and insert piping.

To sew cording:

1. Set machine for „Coverstitch narrow”, using needles D&E

2. Raise the presser foot and change to “Cording foot”.

3. Snap the “Cording Guide” into the hole at left front of stitch plate and in the gap between rolled hem lever and coverstitch-cover.

4. Note: cord diameter of up to 1/16” (2.0 mm) can be used.

5. Insert cord into the hole of the “cording guide”, then through the groove of the “cording foot”.

6. Pull the cord tail about 2” (50 mm) behind the foot.

7. Slide fabric under foot and above the cord.

8. Lower the presser foot and sew, while guiding the cord behind the foot when beginning to sew.

To sew Piping:

1. Set machine for „Chain Stitch”, using needle D.

2. Raise the presser foot and change to “Cording foot”.

3. Note: “Cording guide” is not used for this function.

4. Note: cord diameter of up to 1/16” (2.0 mm) can be used.

5. Insert cord through the groove of the “Cording foot”.

6. Wrap fabric around cord in front of foot. Slide fabric under foot.

7. Lower the presser foot and sew over fabric.

8. Note: Hold cord behind the foot when beginning to sew.

This presser foot guides decorative and fine cords of up to 2 mm thickness exactly and precisely below the coverstitch seam as they are being sewn on.
Alternatively, it can also be used to create and insert piping.

Video

Istaknuti proizvodi

...

Product has been added to your list.